THIS APPLIES TO FXO ONLY IF YOU HAVE FXS CHANNEL ISSUES IT IS NOT ADDRESSED IN THIS DOCUMENTATION
If you are having problems setting up these products then you are not alone. Here is a List of issues that I've run into and How I solved these issues.
1. Getting the darn thing to work at all.
2. Getting CallerID to work correctly
3. Echo and Static issues
4. Volume issues
5. Call Pickup Issues
6. Support Issues
First of all make sure you have the documentation open and handy as you read this you can reference the commands I will give you in there and get more in depth information.
LINK IS BROKEN (leaving it in just in case someone finds it again)
http://www.audiocodes.com/asp/DisplayFoldersFiles2.asp?FolderID=1135
Click on the full Users Manual
The First Issue I had was solved by making the Gateway work as a whole. I tried doing all the things I did previously with other gateways like the Grandstream and the Clippcomm (btw never get a Clippcomm if you want a working product) to no avail. I did everything I though was right so I ended up finding a Config file as a starting point to move forward. Which you may need so I will give you it here.
Example Config File:
Okay. So what I am going to focus on are two areas. Voice Engine Params and Sip Params
Those are the two pertinent areas. There are several How-To's out there that tell you to turn off autodial. Not sure why because thats what ended up getting everything to work for me in the end.
Under Sip params I want you to notice a few settings. The Username and password and the ProxyIP.
If you are having problems setting up these products then you are not alone. Here is a List of issues that I've run into and How I solved these issues.
1. Getting the darn thing to work at all.
2. Getting CallerID to work correctly
3. Echo and Static issues
4. Volume issues
5. Call Pickup Issues
6. Support Issues
First of all make sure you have the documentation open and handy as you read this you can reference the commands I will give you in there and get more in depth information.
LINK IS BROKEN (leaving it in just in case someone finds it again)
http://www.audiocodes.com/asp/DisplayFoldersFiles2.asp?FolderID=1135
Click on the full Users Manual
The First Issue I had was solved by making the Gateway work as a whole. I tried doing all the things I did previously with other gateways like the Grandstream and the Clippcomm (btw never get a Clippcomm if you want a working product) to no avail. I did everything I though was right so I ended up finding a Config file as a starting point to move forward. Which you may need so I will give you it here.
Example Config File:
;**************
;** Ini File **
;**************
;;Board[:] MP-114 FXO
;;Serial Number[:] 875328
;;Slot Number[:] 1
;;Software Version[:] 4.80A.025.004
;;Board IP Address[:] 192.168.6.10
;;Board Subnet Mask[:] 255.255.255.0
;;Board Default Gateway[:] 192.168.6.1
;;Ram size[:] 32M Flash size[:] 8M
;;Num DSPs[:] 1 Num DSP channels[:] 4
;;Profile[:] NONE
;------------------------------
[SYSTEM Params]
SyslogServerIP = 10.1.1.89
[BSP Params]
PCMLawSelect = 3
LocalOAMIPAddress = 192.168.6.10
RoutingTableHopsCountColumn = 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
[ATM Params]
[Analog Params]
FarEndDisconnectSilenceMethod = 0
CallProgressTonesFilename = 'usa_tones_12.dat'
[ControlProtocols Params]
[MGCP Params]
[MEGACO Params]
EP_Num_0 = 0
EP_Num_1 = 1
EP_Num_2 = 0
EP_Num_3 = 0
EP_Num_4 = 0
[SS7 Params]
[Voice Engine Params]
IdlePCMPattern = 85
ECDCremoval = 1
ECNLPMode = 0
ECNlpSensitivity = 1
EchoCancellerAggressiveNLP = 1
InputGainLocation = 1
InputGain = 0
VoiceVolume = 4
[WEB Params]
LogoWidth = '339'
[SIP Params]
ENABLECALLERID = 1
MAXDIGITS = 14
TIMEBETWEENDIGITS = 5
REGISTRATIONTIME = 3600
ISPROXYUSED = 1
ISREGISTERNEEDED = 1
AUTHENTICATIONMODE = 1
ISTWOSTAGEDIAL = 0
CDRREPORTLEVEL = 1
GWDEBUGLEVEL = 5
PROXYNAME = '192.168.6.5'
SIPGATEWAYNAME = 'audiocodes.com'
USERNAME = 'mp_fxo'
CNONCE = '0a123bcf'
PASSWORD = '***'
PROGRESSINDICATOR2IP = 1
ISFAXUSED = 1
CODERNAME = g711Ulaw64k,20,0,$$,0
CODERNAME = g729,20,0,$$,0
PREFIX = 10,192.168.6.5,*,0,255
PREFIX = 20,192.168.6.5,*,0,255
PREFIX = *,192.165.6.5,*,0,255
PSTNPREFIX = *,1,*,*,0
TARGETOFCHANNEL0 = 600,1
TARGETOFCHANNEL1 = 600,1
TARGETOFCHANNEL2 = 600,1
TARGETOFCHANNEL3 = 600,1
TRUNKGROUP_1 = 1-4,201,0
PROXYIP = 192.168.6.5
AUTHENTICATION_0 = mp_fxo,250
AUTHENTICATION_1 = mp_fxo,250
AUTHENTICATION_2 = mp_fxo,250
AUTHENTICATION_3 = mp_fxo,250
TRUNKGROUPSETTINGS = 1,1
TRUNKGROUPSETTINGS = 2,1
TRUNKGROUPSETTINGS = 3,1
TXDTMFOPTION = 4
;;TelProfile[:] ProfileName, Preference, CodersGroupID, IsFaxUsed, DJBufMinDelay, JBufOptFactor, IPDiffServ, SigIPDiffServ, DtmfVolume, InputGain, VoiceVolume, EnableReversePolarity, EnableCurrentDisconnect, EnableDigitDelivery, ECE, MWIAnalog, MWIDisplay, FlashHookPeriod, EnableEarlyMedia, ProgressIndicator2IP
TELPROFILE_1 = Default Tel Profile,1,0,1,70,7,46,46,-11,0,1,1,0,0,1,0,0,400,0,1
ENABLECALLERID_0 = 1
ENABLECALLERID_1 = 1
ENABLECALLERID_2 = 1
ENABLECALLERID_3 = 1
[VXML Params]
[IPsec Params]
[Audio Staging Params]
[PSTN-SDH Params]Okay. So what I am going to focus on are two areas. Voice Engine Params and Sip Params
Those are the two pertinent areas. There are several How-To's out there that tell you to turn off autodial. Not sure why because thats what ended up getting everything to work for me in the end.
Under Sip params I want you to notice a few settings. The Username and password and the ProxyIP.